Match the bulb to your fixture before you order
A modeling bulb is the wrong place to guess. The JDD Type 250W 110V E27 frosted halogen bulb is built for studio strobes that use a standard Edison screw base, and the supplied record lists Fotodiox L, TS, M, H and YS series strobes as the intended fixtures. Check your own fixture's socket and voltage first, then use the product facts below to confirm the rest.
The supplied information does not list a maximum wattage for every fixture or a universal cross-reference for other brands. Treat that as a limit on what can be confirmed here, not as a claim about what your fixture can or cannot accept.
What the JDD 250W record confirms
- JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: 250 watt / 110 volt halogen modeling bulb for studio strobes Wattage and voltage are the two numbers to match against your fixture and supply before ordering.

JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes - JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: E27 Edison Standard screw-in base, suitable for standard E26/E27 screw studio lamp modeling 250W bulbs The screw base is the fit checkpoint; confirm your strobe uses this standard base rather than a bayonet or proprietary mount.
- JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: Tungsten ~3200°K color balance with frosted glass The tungsten balance tells you what kind of modeling light you are adding, and the frosting softens the bare-bulb output.
- JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: Average rated life ~2,000 hr This is the manufacturer's average rating, not a guarantee for every individual bulb or fixture.
Three checks that decide the purchase
Run these checks in order. If any one fails, the bulb is not the right replacement for that fixture.
- Voltage: This is a 110V bulb. Confirm your strobe's modeling circuit is supplied at the voltage the fixture is designed for. Do not assume a 110V bulb suits a higher-voltage modeling circuit.
- Base: The record specifies an E27 Edison Standard screw base and describes it as suitable for standard E26/E27 screw studio lamp modeling bulbs. Inspect the socket on your strobe before ordering.
- Fixture family: The supplied record names Fotodiox L, TS, M, H and YS series strobes as the designed fixtures. If your strobe is outside that list, the supplied information does not confirm fit.
Where the frosted JDD bulb makes sense
Choose this bulb when you want a tungsten-balanced modeling light in a standard screw-base strobe and your fixture is on the supported list. The frosted envelope is useful when a bare quartz halogen bulb would be too harsh or too visible in the reflector, and the ~3200°K balance keeps the modeling light in the tungsten family.
The 250W rating is a fixed specification, not a dimming recommendation. The supplied record does not describe dimming behavior or a dimming range, so do not treat this bulb as a dimmable modeling solution unless your fixture's own documentation supports it.
Where it is not the confirmed choice
Skip this bulb if your strobe uses a different base, if your modeling circuit is not a 110V design, or if your fixture is not among the Fotodiox series named in the record. In those cases the supplied information does not establish compatibility, and a different replacement should be sourced from the fixture's own documentation.
The record also does not include installation steps, warm-up or cool-down guidance, or handling instructions for the quartz halogen envelope. Those details are not confirmed here, so follow the fixture manufacturer's own procedures rather than improvising.
Size, warranty and catalog details
- JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: Product dimensions 1.2 x 1.2 x 4.1 in (3 x 3 x 10.5 cm) at 0.1 lb (2.1 oz) Useful for checking clearance inside a reflector or housing before the bulb arrives.
- JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: Limited 2-year manufacturer warranty (listed as limited 24 months) The warranty term is part of the value comparison against a generic replacement.
- JDD Type 250w 110v E27 (Standard Edison Screw) Frosted Halogen Light Bulb, Replacement Modeling Bulb for Strobes: Catalog price USD 28.76, shown against a catalog comparison price of USD 39.95 Gives you the listed price context at the time of writing; confirm current pricing at checkout.
How to order the right replacement
Write down your strobe's series and socket type, then compare them with the E27 base and the Fotodiox L, TS, M, H and YS series list in the record. Confirm the 110V and 250W figures against your fixture's own labeling. If all three match, the JDD frosted halogen bulb is the confirmed replacement path; if any one does not, the supplied information is not enough to recommend it for your setup.
Product pictures are for illustration only, and the manufacturer notes that the actual product may vary slightly due to ongoing design improvements. Use the written specifications, not the photo, as your buying reference.


